Tutorial: How to sew on the Meringue waistband


Yesterday, we showed you how to draft your own waistband for the Meringue skirt, since the original design has a simple facing at the waist. Today, we’ll just go through the steps for attaching it.

Cut out all the pattern pieces including the waistband and interfacing. Remember that you won’t need the waist facing pieces for this skirt since you’ve made a waistband.

Apply the interfacing to front and back pieces. Be sure to use a press cloth to avoid any iron mishaps.

The zipper is on the left side of the skirt. Sew the non-interfaced waistband pieces together along one seam as shown. This will be the waistband on the right side of the skirt. Sew the interfaced waistband pieces together along one seam as shown. This will be the waistband on the inside of the skirt.

Put waistband and interfaced waistband right sides together.

Place pins about 1 1/2″ from the top edge. This is where you’ll begin and end sewing. The unsewn portion is left open for the time being. Sew between the two pins.

Pin the waistband to the skirt, right sides together. Make sure the side seams match up.

Sew the waistband to the skirt.

Serge or pink the seam to finish it.

Iron the waistband, making sure that the seam you just sewed is pressed upwards, into the waistband.

Position the invisible zipper and install using this handy tutorial.

Once the invisible zipper has been installed, place the interfaced waistband over the zipper as shown. Sew the remainder of the seam closed. Stitch over the zipper coil all the way to the end. Do this for both sides.

Put a zipper foot into your machine. Sew 5/8″ from the edge or as close as you can get to the invisible zipper coil. Be sure not to catch the coil in your stitches. Before you reach the end, fold up the waistband about 3/8″ and backtack to finish.

Serge or pink the top of the waistband seam.

Trim and grade the corners of the waistband. Take care not to cut into the seam. Use a point turner to flip right side out. Check out this tutorial for point turner tips.

Iron the top of the waistband. Making sure that the inner waistband stays to the inside and doesn’t peep out into the right side.

Iron under 3/8″ of the interfaced waistband. There should be enough of the waistband to be caught when you stitch in the ditch.

Sewing slowly, stitch in the ditch. This will keep the inner waistband in place. And you’re through!

Caitlin Clark   —  

Caitlin is the Colette Patterns design assistant. You can follow Caitlin at her blog, the story girl.

More about our writers

Comments 20

raquel from florida

Great tutorial! Can you show a picture of the finished zipper on the right and wrong sides?

CGCouture countrygirlcouture.wordpress.com

Wanted to come out of lurking to say thanks for this tutorial, waistbands are one of those things that I sometimes goof up. OK, maybe I goof them up often…especially the corners by the zipper.

Sarah rhinestonesandtelephones.blogspot.com

Excellent tutorial and very timely. Meringue is on my to sew list. :)


thanks for the tutorial. what kind of interfacing do you use?

Sarai colettepatterns.com

It depends on the project and on the fabric, really. For fusibles, Caitlin and I both prefer a very lightweight interfacing, because the fusing actually adds more stiffness. So I often recommend choosing an interfacing a bit lighter than your fabric. Right now, we’re using a lot of a knit featherweight interfacing.

I also someimes interface with fabrics, like silk organza or muslin. It just depends what I’m sewing and how much weight and stiffness is needed. :)

Sarah sarahsewing.blogspot.com

Do you use a special foot for in the ditch stitching? Mine is so abysmal that I usually end up hand stitching waistbands on the inside.

Sarai colettepatterns.com

The one shown is just a standard presser foot, but I often use an edgestitching foot (Bernina #10) for stitching in the ditch.


Totally unrelated topic, but have you seen this 1940s pattern cover? It’s the Sencha with the Ginger! So cute! I need to get the Sencha pattern now so I can wear this chick’s outfit.



That IS very cute! :)


THANK YOU for the WONDERFUL STEP-BY-STEP TUTORIALS. I am just returning to sewing.



A bit confusing when you say, “Apply the interfacing to front and back pieces,” but mean only one set of the front and back pieces. Right? One front and back is interfaced, and one is not, even though you imply that they should all be interfaced? Thanks.


I have the same doubt as Erica, I’m getting lost somewhere between sewing the right side of the facings together to when they are sewn to the skirt and how tomplace them! Please help! I’m stuck in my Meringue and I’m starting to get frustrated!


Hi Erica, I found this tutorial and together with Sarai I think I have it figured out!


Michelle sewplaysew.wordpress.com

how would you alter this or do it differently for a lined skirt with this type of waistband?

Black Jacquard Meringue Skirt | Blanca Pate

[…] waistband, according to the pattern adjustment and sewing tutorials on the Coletterie […]

Taaskasutus: kleidist seelikuks | Kohustuslik tegevusvabadus

[…] eelmise õmbluse jälgedesse. Sellest nüüd küll muidugi piltideta aru ei saa, aga vaadakse selle õpetuse viimast etappi (stitch in the ditch on see tehnika). Aga elu tahtis sedasi, et värvli […]

The Full, Gathered Skirt | sewplaysew

[…] print ( I’d also love to do it in tafetta like Gertie). I think next time I will try  use this tutorial from Coletterie  for the zipper/waistband insertion instead of the one Gertie uses. I want to see if it’s an […]

Pink Peonies Skirt | sewplaysew

[…] waistband technique in which you enclose the zipper in the waistband at the back. I got the tutorial here. I really like this technique and think it makes the skirt look more […]

Õmblesin lihtsa seeliku | Kohustuslik tegevusvabadus

[…] näha, et värvli mõlemad otsad on sama laiad. Saavutus seegi. Värvli õmblemisel järgisin neid juhiseid, olid teised väga kasulikud. Seega puudujääke on, aga olen rahul, kuna seelik tundub […]


thank you so much for this super tutorial!

We’re sorry, comments for this post have been closed.

Printed from the Colette Blog


Get all of our tips, tutorials, and discussions delivered to your inbox — completely free!